11/21/2011

Installation

In the case where the installation of plastic windows is not part of a comprehensive renovation, there is a problem finishing slopes. At the moment, many organizations involved in the installation of windows, provide a similar service. However, the question often trim window slopes appeared just after installing windows. Quite possible to make the slopes of the drywall itself. When installing the plastic windows on the slopes is untreated strip width of about 5-30 cm This entails finishing the entire slope, and sometimes further repairs.

The cost of work includes interior and exterior finishing of the slope, the dismantling of old slopes (if necessary) painting, installation of the sill, if the service is not included in the cost of installing windows. One common misconception is that the protective film must be removed from the windows after the installation, and it leads to the fact that when working on slopes disturbed profile window. Should work with slopes for some reason delayed or damaged protective tape on the panel, before doing finishing work must be reserved by masking tape. So not worth it for a long time to leave without finishing cut off the mounting foam on the outer slopes - it is hygroscopic and can accumulate moisture and dampness in the future be in repose. If the foam is cut and finish in the near future threatened, the best option - enamel paint to cover the porous surface of the slice. The most common variant of slopes finish - plaster gipsosoderzhaschimi mixtures. It is most economical but least practical. The service life of slopes ranging from 3 to 10 years.

One of the major drawbacks is that the plaster works can be damaged and the window sill profile. And the mixture did not tally with the profile itself, which is also in further cracks and delamination provides. Quite often on slopes installed drywall construction. This method is more reliable, however, it is worth remembering that these slopes require further finishing. Easy enough, and inexpensive way - finishing a cellular plastic, but when the slope of 25 cm wider, it becomes necessary to attach the edge of plastic, but it significantly reduces the appearance of the slope. One of the best options is to finish sandwich panels. Their size is 1500 * 3000. This makes it possible to mount the slopes without joints. A positive factor is the longevity of such panels. The slopes of the plastic sheet are durable, high quality, have a perfect appearance form. The only drawback - high enough price. The choice of type of finish is up to you - a more economical, or more practical, but it is worth remembering that without finishing the set of slopes box does not give you the desired sound and insulation. And if this article inspired you on the slopes with their hands do not hesitate to get to work
Nov 21, 2011 9:34:04 PM

Verify your Comment

Previewing your Comment

Posted by:  | 

This is only a preview. Your comment has not yet been posted.

Working...
Your comment could not be posted. Error type:
Your comment has been posted. Post another comment

The letters and numbers you entered did not match the image. Please try again.

As a final step before posting your comment, enter the letters and numbers you see in the image below. This prevents automated programs from posting comments.

Having trouble reading this image? View an alternate.

Working...

Leave a comment

(URLs automatically linked.)

Your Information

Name and email address are required. Email address will not be displayed with the comment.

NEXT POST
Concrete Floors Without Cracks Diamond cutting straight seam is widely used in the construction, renovation and modernization of large industrial buildings and civil structures (shops businesses, warehouses, logistics and retail and entertainment centers, supermarkets, train stations, stadiums, stations, parking lots). Concrete horizontal coverage of such structures must withstand considerable dynamic loads for a long time. However, in concrete with some internal tensions and external action is chaotic cracking up to the total destruction and unfit for further operation. Despite the fact that the concrete - one of the most enduring material, its structure is very fragile and non-plastics. Drying and solidification, poured concrete shrinks, while the upper part dries faster and more reduced in volume, the edges start to wrap. There is an internal tension, and concrete cracking. Cracks causes and effects of environmental conditions (sudden changes in temperature, ground water, subsidence of soil under the concrete base, landslides and earthquakes), and intensive load during its further operation (traffic, walking a lot of people work heavy equipment). Therefore, in order to prevent uncontrolled cracking of concrete ties industrial floors, at some stage in accordance with strict regulations are cut so-called expansion joints. The main and most commonly used types of them - Contraction joints and insulation. Modern diamond Technology makes it easy, quickly, accurately and with virtually no noise and litter quality cut joints that do not need to continue to polish and correct. At this speed, quality, cutting sutures and the end effect is much higher than with traditional jointing uncured concrete floors. Cutting joints held not earlier than 12-24 hours after pouring the concrete screed and no later than 2-3 days. Concrete must have hardened, but not to the extent that begin to appear random cracks. Sutures are cut by experienced specialists in strict accordance with the project - with strict observance...
PREVIOUS POST
Construction Claydite So, you peshili build for themselves and their family country house with more or less nebolshimi vlozheniyami. Where should you start? To begin with oznakomtec glavnymi nopmami ppoektipovaniya ychactka c zastpoykami pazlichnogo plan, where all ychityvayutsya canitapnye and ppotivopozharnye requirements. This is necessary in order to oppedelit camoe optimalnoe place pacpolozheniya bydyschego letnego your house. Choosing stpoymaterialov Vcem izvestno that nachalo any construction - is the choice of construction and poick matepialov. Ppaktichecki each xochet that this material was the Most ne tolko teploeffektivnym, environmentally friendly, but also have acceptable, doctypnyyu price. Ponyatie date every year domik of nas ponimaet in paznomy: for whom He is a regular or depevyannaya kippichnaya konctpuktsiya, kotopaya yavlyaetcya an integral part of suburban ychactka, a for-whom He poctpoyka it, vpitavshayacya a vce strength, love and bolshoe kolichectvo zatpachennogo time. In lyubom cluchae, absolyutno kazhdomy xochetcya not build a house nA one season, and on dolgie years. Spok Survey, poctroennogo home in mnogom depends on the durability of the walls, so they dolzhny obladat cootvetstvovat ystanovlennym nopmam teplozaschitnyx kachectv be mopozoctoykimi, vozdyhopronitsaemymi and poddepzhivayuschimi indoors nyzhny MODE temperatypy and vlazhnocti. K.pome this takzhe necessary to walls had oppedelennye zvykoizolyatsionnye xapakterictiki and meet texnicheckim tpebovaniyam. Price to takie ctpoymaterialy high, but there is ppekpacnaya altepnativa, tolko on more priemlemoy tsene. One is takix matepialov claydite, kotopy mozhno ppigotovit directly nA place where razvepnylac building. Pochemy vcego more suitable for the construction of claydite? House, poctroenny of keramsit, will be played have pyadom nekotoryx ppeimyschectv, kotopye day oto day are played to please his xozyaina, and it is not dostypnaya only price but also quality. The notion that only the y PRODUCTS yzhacnogo quality mozhet be a small price to keramsit in any case not applicable. Delaetsya claydite of ekologicheski chictogo matepiala-clay pellets. He predctavlyaet a vcpenennyyu...